2018 F2 unveiled in Monza
The FIA Formula 2 Championship unveiled the F2 2018 to the international media in Monza today. The new car, which will be raced in the 2018, 2019 and 2020 seasons, was revealed in the Formula 1 paddock ahead of the 9th Round of the 2017 F2 season.
The new car, which complies with the latest F1 safety standards, features architecture typical of a modern F1 car and a 3.4 liter turbo-charged Mecachrome engine, which delivers 620 HP at 8,750 rpm. The design philosophy was to refresh the car to mirror the latest updates in F1 design, and to maintain a long tradition of wheel to wheel racing.
The safety updates include changes to marshaling such as the Virtual Safety Car (VSC), Drag Reduction System (DRS) and upgraded electronics, and most notably is the first new car to be revealed featuring the Halo system, which was incorporated at the final stage of the design process.
The electronics have been enhanced with an updated ECU, which features expanded evolution possibilities for later years in an effort to future proof these components, a design decision which is in line with the usual focus on cost control. The operational costs for the teams are expected to be similar to this year.
Two test sessions in December will be solely focused on performance testing, where the car will be pushed to its limits ahead of the handover process to the teams. A first car will be delivered to the teams in mid-January 2018, and the second car will be delivered in mid-February. There will be a shakedown with the teams between these dates to allow them to become acclimatized with the car ahead of the first official pre-season test.
Pirelli is once again the official tire supplier to the championship, and has been integral to the design process to ensure continuity with respect to the tires.
Charlie Whiting, FIA Director of F1 and Director, Single-Seater Department commented: “The unveiling of the 2018 FIA Formula 2 car is an important moment for the FIA as we complete the single-seater pyramid from Karting right through to the pinnacle of motor sport in the FIA Formula One World Championship.
“The plan for a more structured junior formula ladder is designed to feature cars that better prepare drivers for the next step. For Formula 2, that means we needed a car that will not only educate, but will also allow the drivers that are most ready for Formula One to shine brightest.
“The car has been developed to include improved aesthetics, as well as bringing the safety level up to the highest standards for single-seater cars – and to ultimately bring it closer to a modern Formula One car on both of these points.
“We are proud to present the 2018 FIA Formula 2 Championship car alongside the Promoter, Formula One Management, and we look forward to our continued partnership at this level with this exciting new car.”
FIA Formula 2 Championship CEO Bruno Michel said: “I am very pleased to be able to present our new car for the next three year cycle of the FIA Formula 2 Championship. Our focus has always been on providing a powerful, safe and challenging car which will encourage overtaking, and thanks to the new aerodynamics package we believe this car will both enhance racing and provide even more entertainment for our fans. Our philosophy has always been to match this with cost control for the teams, and we believe the F2 2018 will continue to limit operational costs and provide an attractive package to our teams.
“Finally, and most importantly, the F2 2018 matches the very latest F1 safety standards: we have a strong track record on safety, and this was a principle focus during the design process. I believe that the F2 2018 is the right car for the next stage of our championship, while also providing a worthy race car for the final step of the motorsport ladder for our drivers hoping to achieve their ultimate ambition: a race seat in F1.”
The F2 2018 car specs
Overall length: 5224 mm (was 5065mm)
Overall width: 1900 mm (unchanged)
Overall height: 1097 mm including FOM roll hoop camera (was 1072 mm)
Wheelbase: 3135 mm (was 3120mm)
Overall weight: 720 kg (driver on-board)
Rated to 620 HP @ 8750 rpm
Fly by wire accelerator system
Rebuild after 8000 km
Maximum Torque 600 Nm
Acceleration: 0 - 100 km/h, 2.90 sec
Acceleration: 0 - 200 km/h, 6.60 sec
Maximum speed: 335 km/h (Monza aero + DRS)
Max. braking deceleration -3.5 G
Halo F1 specification
Monocoque and Bodywork
Survival cell - Sandwich Carbon/aluminum honeycomb structure made by Dallara
Front and rear wing - Carbon structures made by Dallara
Bodywork - Carbon - Kevlar honeycomb structures made by Dallara
Same functionality of DRS used in Formula One
6-speed longitudinal Hewland sequential gearbox
Electro-hydraulic command via paddle shift from steering wheel
ZF SACHS Carbon clutch
No on-board starter, anti-stall system
Non hydraulic ramp differential
Premier FT5 125 liters
Magneti Marelli SRG 480 ECU/GCU including data logging system
Magneti Marelli PDU 12-42 power supply management unit
CAN data acquisition pre-equipment
Double steel wishbones, pushrod operated, twin dampers and torsion bars suspension (F) and spring suspension (R)
Adjustable ride height, camber and toe
Two way (F) / Four way (R) adjustable Koni dampers
Adjustable anti-roll bar (Front/Rear)
6 pistons monobloc Brembo calipers
TBC carbon-carbon brake discs and pads
Wheels and tires
F1 2016 standard wheel dimensions
13” x 12” front F1 2016 standard wheel dimensions
13” x 13.7” rear F1 2016 standard wheel dimensions
F2 specific Pirelli slick / wet tires
Non-assisted rack and pinion steering system
XAP steering wheel with dashboard, gear change and clutch paddles, marshaling & VSC display
Roll hoop, nose cone and face shot camera pre-equipment.
Feedback can be sent to firstname.lastname@example.org
Go to our forums to discuss this article